| ET 200S COMPACT, 16DI/16DO STD DC24V, 3MS; DC24V, 0.5A EXPANDABLE WITH UP TO 12 ET 200S MODULES (NO F-MODULES) ELECTRONICBLOCK |
| General information |
| Vendor identification (VendorID) | 8200H |
| Supply voltage |
| Rated value (DC) | 24 V |
| Reverse polarity protection | Yes |
| Input current |
| from supply voltage 1L+, max. | 100 mA |
| Address area |
| Addressing volume |
| Outputs | 100 byte |
| Inputs | 100 byte |
| Digital inputs |
| Number/binary inputs | 16 |
| Input voltage |
| Type of input voltage | DC |
| Rated value, DC | 24 V |
| for signal "0" | -30 to +5 V |
| for signal "1" | 13 to 30 V |
| Input current |
| for signal "1", typ. | 3 mA |
| Input delay (for rated value of input voltage) |
| for standard inputs |
| at "0" to "1", min. | 3 ms |
| at "0" to "1", max. | 3 ms |
| Cable length |
| Cable length unshielded, max. | 1000 m |
| Digital outputs |
| Number/binary outputs | 16 |
| Functionality/short-circuit strength | Yes |
| Limitation of inductive shutdown voltage to | L+ (-55 to -60 V) |
| Lamp load, max. | 5 W |
| Controlling a digital input | Yes |
| Output current |
| for signal "1" permissible range for 0 to 60 °C, min. | 7 mA |
| for signal "0" residual current, max. | 0.5 mA |
| Output delay with resistive load |
| 0 to "1", max. | 0.5 ms |
| 1 to "0", max. | 1.3 ms |
| Switching frequency |
| with resistive load, max. | 100 Hz |
| with inductive load, max. | 2 Hz |
| on lamp load, max. | 10 Hz |
| Aggregate current of outputs (per group) |
| Digital inputs / Number of inputs that can be driven in parallel / all mounting positions |
| up to 60 °C, max. | 2 A |
| Cable length |
| Cable length unshielded, max. | 1000 m |
| Encoder |
| Connectable encoders |
| 2-wire BEROS | Yes |
| permissible quiescent current (2-wire BEROS), max. | 1.5 mA |
| Interfaces |
| Interface physics, RS 485 | Yes |
| Interface physics, FOC | No |
| Supports protocol for PROFINET IO |
| Transmission rate, max. | 12 Mbit/s |
| PROFIBUS DP |
| Cable length, max. | 1200 m |
| PROFIBUS DP, output current, max. | 80 mA |
| Transmission procedure | RS 485 |
| Direct data exchange (slave-to-slave communication) | Yes |
| Protocols |
| Supports protocol for PROFINET IO | No |
| Protocols (Ethernet) |
| TCP/IP protocol | No |
| Further protocols |
| PROFIBUS DP protocol | Yes |
| Isochronous mode |
| Isochronous mode | No |
| Interrupts/diagnostics/status information |
| Alarms |
| Alarms | No |
| Diagnoses |
| Diagnostic functions | Yes |
| Diagnostics indication LED |
| Run mode RUN (green) | Yes |
| Group error SF (red) | Yes |
| Status indicator digital output (green) | Yes |
| Status indicator digital input (green) | Yes |
| Monitoring 24 V voltage supply ON (green) | Yes |
| Connection to network LINK (green) | No |
| Transmit/receive RX/TX (yellow) | No |
| Galvanic isolation |
| between backplane bus and electronics | No |
| between supply voltage and electronics | No |
| Galvanic isolation digital inputs |
| Galvanic isolation digital inputs | No |
| Galvanic isolation digital outputs |
| Galvanic isolation digital outputs | Yes |
| Isolation |
| Isolation checked with | 500 V DC |
| Degree and class of protection |
| IP20 | Yes |
| Connection method |
| Inputs/outputs | Screw-type and spring-loaded terminals, permanent wiring; 3 and 4-wire connection |
| Dimensions |
| Width | 120 mm |
| Height | 81 mm |
| Depth | 58 mm |
| Weight |
| Weight, approx. | 230 g; EB only |
